Suppliers with verified business licenses
Audited Supplier Product description of wave jigging machine:
Sawtooth wave jigging machine is one of the key equipment of gravity separation. Due to its handling capacity is big, wide size range, high recovery rate, the effect is good, therefore, widely used in separating placer gold, tin, tungsten, lead, zinc, antimony, manganese, diamond, iron ore and other nonferrous metallurgical mining and gold mining ship. And this kind of product of JT4-2, JT1.5 - type 2 sawtooth wave jig, big grain feed particle size can be up to 30 mm biggest, using sieve sieve bottom on mine. It is applied to ore beneficiation of barite, manganese ore, iron ore, etc., it has the advantage of reducing the size of the ore and reducing the water supply.
More than the traditional jig for circular eccentric drive, the jig pulsating curve is sine waveform more, because the diaphragm the effects of the flow rate of rise and fall and movement have the same time, therefore, does not favor the jigging bed loose and particles according to the proportion of layered, thus affecting the separating ratio and recovery equipment.
Product features of wave jigging machine:Sawtooth wave jig is according to the laws of the jigging bed theory stratification, based on the traditional jig for development and improvement of a re-election energy-saving equipment, the jig pulsating curve shows zigzag, faster than the drop flow make up water: short rise time, fall time is long; Overcome the sine wave, pulse curve of jig flow and function of rise and fall time of the same defect, enhance the bed layer loosely, alleviate the suction effect, make full settlement of the heavy mineral particles in the mineral, greatly improving the seeding than ability and the recovery rate of the equipment. The comparison of the jigging machine with sine wave was improved: Sn 3.01%, W 5.5%, Pb 1.63%, Zn 2.04%; The water consumption is reduced by 30% to 40%, and the area is reduced by 1/3, and the stroke can be adjusted. Its performance reaches the domestic advanced level and is one of the ideal energy saving and reselecting equipment.
Working principle of wave jigging machine:
Jig belongs to deep - groove type selection equipment. All jigging machines have jig. An organization that encourages water movement and a product discharge mechanism. Jigging sieve plate by punching plate, indoor woven mesh or article Bi iron, water flow through the sieve plate into the jigging chamber should be the height of the bed is rising and are slightly loose status, the density of particles due to the partial pressure and velocity for bigger and into the underlying, density of small particles are transferred to the upper. When the water drop, dense tiny particles can also be through gradually close clearance to enter the lower bed layer, added according to the density of the layered agitating flow mechanism in the early years of the pistons, piston chamber in jigging chamber side, lower connected, by the eccentric connecting rod mechanism to drive the piston moves up and down.
| LTA series jig technology parameters: | |||||||
| Model number | Coefficient of stroke | stroke(mm) | At times(/min) | Feed particle size(mm) | Handling capacity(T/h) | Water consumption(T/h) | power(KW) |
| LTA55/2 | 0.5 | 0-25 | 250-350 | 8 | 1-5 | 4-20 | 1.5 |
| LTA1010/2 | 0.5 | 0-25 | 250-350 | 8 | 5-20 | 20-60 | 3 |
| LTA1515/2 | 0.5 | 0-50 | 200-300 | 10 | 15-25 | 100-140 | 5.5 |
| LTA2020/2 | 0.5 | 0-50 | 200-300 | 10 | 30-50 | 160-200 | 7.5 |
| AM-30Technical parameters of jigging machine: | |||||||||
| Model number | Cross section form | The number of columns | Jigging room number | Jigging area() | Coefficient of stroke | stroke(mm) | At times | processing(T/h) | power(KW) |
| AM-30 | rectangular | Double row | 4 | 2.574 | 0.47 | 0-50 | 130-160 | 10-15 | 3 |
| projects | Jigging chamber | The diaphragm | Feed particle sizemm | Sieve the water supplym3/t | Make-up pressureMpa | processingt/h | powerkw | External dimensionmm | weightkg | remark | ||
| parameter | ||||||||||||
| Model number | shape | aream2 | strokemm | At times (times/min) |
||||||||
| JT0.57-1 | trapezoidal | 0.57 | (M12CAM)8.5-12 | 80-180 | <6 | 1-2 | ≥0.05 | 1.5-3 | 1.5 | 1550×780×1530 | 610 | |
| (M17CAM)10-17 | ||||||||||||
| JT1-1 | trapezoidal | 1.04 | <10 | 2-3 | 2.5-5 | 2.2 | 2270×1110×1890 | 900 | ||||
| JT2-2 | rectangles | 2.28 | (M21CAM)12-21 | <10 | 2-4 | 5-10 | 3 | 3225×1550×2050 | 1640 | |||
| JT3-1 | trapezoidal | 3 | 12-30adjustable | 50-125 | <10 | 3-6 | ≥0.05 | 7.5-15 | 5.5 | 2745×2000×3030 | 3085 | |
| JT4-2 | rectangles | 4 | 25-57Five kinds of CAM adjustable | <25 | 4-8 | 8-20 | 7.5 | 4240×1990×2750 | 3098 | Large grain jigging machine | ||
| JT4-2A | rectangles | 4 | 25-5Five kinds of CAM adjustable | <25 | 4-8 | 8-20 | 4×2 | 3500 | Large particle jigging machine dual drive | |||
| JT5-2 | trapezoidal | 4.86 | 12-30adjustable | <10 | 3-6 | 12-25 | 7.5 | 3600×2000×2600 | ||||
Suppliers with verified business licenses
Audited Supplier 
){kind=link}
){kind=link}